Plumbing Basics: A Prerequisite for Installing a Bathtub
Plumbing Basics: A Prerequisite for Installing a Bathtub
Blog Article
Are you currently trying to find guidance about A Step-by-Step Guide to Installing a Bathtub?
Setting up a bath tub isn't specifically brain surgery, yet it does call for solid plumbing, woodworking, and also often, tiling abilities. Replacing an old bath tub with a new one is likewise a reasonably challenging task. If the old bathtub is easily accessible, the project can relocate easily; if you have to open a wall to remove the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either situation, the task is within a home handyman's skills, although you will need a helper to leave the old tub and also embeded in the brand-new one. Make certain you have actually qualified yourself for the task and are comfortable trying it. Rather than employing a professional to take control of a halfway-completed job, it is far better to take into consideration utilizing one before you start. Opportunities are you may require an expert plumber to make tube connections.
This post will help you set up a brand-new bathtub in your washroom if you have already purchased a new tub as well as don't need to change the plan of your previous water system pipelines.
Your devices as well as material list ought to make up the following:
Getting ready for the Setup
To start with, the supporting structure provided with the bathroom must be fitted (if needed) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is essential to make sure that if the tap features a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets system to prevent strain on the bath tub.
Fit the adaptable tap connectors to the bottom of both faucets using 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Make sure you use all of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be fitted in its last setting.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installation, after that the first thing you should do is separate the water system. After doing so, turn on the taps to drain pipes any water continuing to be in the system. The process of eliminating the existing taps can be rather troublesome because of the restricted access that is frequently the case.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the taps. Have a fabric ready for the remaining water that will come from the pipes. Once the supply pipelines have actually been gotten rid of, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from transforming during this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing substance.
Before moving on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Mounting the Tub
Utilizing the two wood boards under its feet, position the bath tub in the needed placement. The wooden boards are handy in equally spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto 4 tiny points.
The following goal is to guarantee that the bath tub is leveled all round. This can be attained by checking the spirit level as well as readjusting the feet on the bath tub till the level reads degree.
To mount taps, fit the bottom of the furthest adaptable faucet port to the suitable supply pipeline by making a compression sign up with; then do the same for the various other tap.
Switch on the water supply as well as check all joints and also brand-new pipework for leaks and tighten them if essential. Fill the bathtub as well as also inspect the overflow electrical outlet and also the regular outlet for leaks.
Finally, fix the bath paneling as explained in the manufacturer's instruction manual. Tiling and securing around the bathtub should wait till the tub has been used a minimum of when as this will certainly resolve it right into its last placement.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will need a plastic connector to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end gives a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will require decreasing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the mounting opening in the bath/basin making sure that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in position with the supplier offered backnut. Once the tap is safely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal faucet connectors. The previous type needs to be linked to the faucet ends first, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bath satisfies the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to fracture an inflexible seal, triggering the water to permeate the wall between the bathroom and also the tiling, causing issues with wetness and possible leaks to the ceiling listed below.
You can choose from a range of coloured sealants to blend in your fixtures and installations. They are sold in tubes and cartridges, and also are capable of sealing voids as much as a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of drenched paper or soft rope. Remember to always load the bathtub with water before securing, to permit the movement experienced when the tub remains in usage. The sealer can crack rather early if you do not take into account this motion before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently readily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water resistant adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you appreciate reading up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Try leaving feedback down the page. We will be glad to listen to your reactions about this blog post. We are looking forward that you come back again in the future. Make sure you take the time to promote this post if you appreciated it. Thanks for taking the time to read it.
Need urgent plumbing repairs? Call. Report this page